Flood irrigation spreads water across a field by gravity, usually through borders, furrows or basins. A rented pump can lift water from a canal, river or pond into a head ditch. It suits hay, pasture and some grains. This guide covers pump selection, field setup and safe operation.
How flood irrigation works
Water enters at the high end of the field and flows across the surface. Borders and berms guide it. Good leveling and flow rates move water quickly enough to avoid deep percolation at the top and dry spots at the bottom.
Compare with renting a sprinkler system for pasture and land leveling equipment rentals.
Choosing a pump
Flood irrigation needs high flow at low head. Axial or large centrifugal pumps are common. Options include PTO, diesel and electric units. See irrigation pump rentals: types and sizing, renting a PTO irrigation pump and renting a diesel irrigation pump. Ask for the pump curve at your lift.
Intake and discharge
Set intake with strainers or screens to keep out weeds and debris. Support suction lines. Discharge into a head ditch or pipe with a controlled outlet. Use gates, siphon tubes or gated pipe to distribute water. See SARE publications, USDA NRCS and your state page.
Leveling and borders
Uneven fields cause ponding and dry corners. Consider laser leveling before flood irrigation. Build or repair borders and berms ahead of time. Check ditch slopes and gates.
Runoff and water rights
Water rights and permits control when and how much you can divert. Check local rules before pumping. Control tailwater so it does not leave your property. Keep fertilizers and chemicals out of runoff. See the EPA agriculture page.
Common mistakes to avoid
- Undersized pump.
- Unleveled fields.
- Ignoring water rights.
- No runoff control.
- Plugged intakes.
Inspect before you accept
Check the pump, driveline or engine, hoses, screens and fittings. Test run. Photograph existing damage. See understanding rental equipment condition reports.
Safety
- Stay away from steep, wet banks.
- Use lockout before service. See the farm machinery lockout-tagout procedure template.
- Keep shields on shafts and belts.
- Keep children away from ditches and pumps.
- Wear boots and keep a rope nearby.
See the OSHA agricultural operations page and CDC NIOSH agriculture.
Transport
Pumps can be heavy. See the equipment transport tie-down checklist and DOT requirements for rented equipment transport.
Costs and terms
Ask about daily and weekly rates, delivery, fuel and deposit. See how to budget for farm equipment rentals and understanding rental agreements.
Planning the set
Walk the field and set the order of borders. Time sets by how long water takes to reach the end. Cut off flow when the water front reaches about three quarters of the way, adjusting for soil. Keep notes for next time.
Troubleshooting
If water advances slowly, increase flow or check leaks. If the end floods, shorten the set. If the pump loses prime, check intake and air. If banks erode, reduce flow or reinforce. Contact the dealer when unsure.
Cleaning and return
Drain, rinse and clean screens. See returning farm equipment: cleaning and fuel rules.
A sample job
A hay grower rents a large PTO pump to lift canal water into a head ditch. The grower repairs borders, checks screens each hour and times each set. The pump is cleaned and returned.
Questions to ask the dealer
- What flow and head can it deliver?
- What power does it need?
- What intake setup is included?
- What are cleaning requirements?
- Can the dealer help with sizing?
Weeds and trash
Floating weeds and trash clog intakes fast. Use a trash rack or screen and check it often. Remove debris safely with a long-handled rake while the pump is off. Keep a spare screen on site.
Keeping records
Record dates, hours, sets and fuel. See record keeping for farm equipment rentals.
Understanding flow rates
Flood irrigation is usually measured in cubic feet per second or gallons per minute. A pump delivering several hundred to thousands of gallons a minute may be needed. Ask the dealer to size the pump to your field area, soil intake rate and the time you have to cover each set. Oversizing wastes fuel, and undersizing leaves the far end dry.
Gates, siphons and gated pipe
Distribute water with canvas dams, slide gates, siphon tubes or gated pipe. Siphon tubes need priming and attention, while gated pipe allows precise control. Check that your ditch and gates can handle the pump's output without overtopping or eroding.
Soil and slope
Heavy clay soils soak slowly and need longer sets, while sandy soils absorb quickly and may lose water below the root zone. Steeper slopes speed water and can erode. Adjust flow, set times and border width to your soil. Your NRCS office can help evaluate soils and irrigation water management.
Night work and monitoring
Many flood sets run at night. Use lights, check safe footing, and make sure someone stays within reach of the pump and gates. Notify a neighbor or family member about your schedule. Never work alone near deep water without a plan for help.
Fuel, power and noise
Plan fuel or electric supply for long sets, because stopping midway wastes water. Place engine-driven pumps away from homes if possible and use hearing protection. Keep fire extinguishers handy and fuel in approved containers.
Environmental care
Keep fertilizer, manure and chemicals from entering ditches that lead to streams. Leave buffer strips where required, and avoid pumping when streams are low if rules limit it. Your NRCS office can advise on practices that protect water quality.
Training helpers
Show helpers how to open gates, read the water front and shut off the pump quickly. Agree on signals before starting, and make sure everyone knows where the shutoff and the emergency contacts are. A short walkthrough prevents flooding the wrong field.
Aftercare for the field
After irrigation, check low spots for ponding, repair eroded berms and note how long each set took. Those notes make next season's irrigation faster and cheaper.
Bottom line
Flood irrigation needs high-volume pumps, level fields and runoff control. Size the pump, protect intakes and follow water rules.
Frequently asked questions
What pump type works best?
High-volume, low-head pumps such as axial or large centrifugal.
Do I need a permit?
Often. Check local water rights and rules.
Should I level first?
Level fields water more evenly.
How do I reduce runoff?
Time sets and control tailwater.