Irrigation pumps move water from a source to a field. Renting one helps with a dry spell, a new field or a repair. The wrong pump wastes fuel and water, so sizing matters. This guide explains pump types, key numbers and set-up. Check your state's water rules before pumping from any source.
Key numbers
- Flow rate. Gallons per minute needed for your system.
- Head. Total pressure and lift the pump must overcome, including elevation, friction in pipes and pressure needed at sprinklers or emitters.
- Suction lift. How high the pump must pull water from the source.
- Power or fuel. Electric, diesel, gas or PTO.
Pump curves show flow at different heads. Ask the dealer to size a pump from your numbers. See SARE publications, the USDA NRCS and your state page.
Pump types
- Centrifugal pumps. Common, efficient and simple. Need priming and limited suction lift.
- Submersible pumps. Sit in the water source. Good for deep wells or ponds.
- PTO pumps. Run from a tractor PTO. See renting a PTO irrigation pump.
- Diesel or gas engine pumps. Portable and independent of electricity. See renting a diesel irrigation pump.
- Trash pumps and dewatering pumps. For dirty water. See renting a trash pump for dirty water.
Matching to the system
Count the sprinklers, drip lines or gated pipe and add their flow. Add pressure needed at the farthest point plus friction losses. Check pipe size, since small pipes lose pressure. Large fields may need more than one pump. Ask the dealer to check your numbers. See center pivot irrigation rentals, drip irrigation equipment rentals and renting a sprinkler system for pasture.
Hoses, fittings and priming
Use hoses rated for the pressure and sized for flow. Suction hoses must not collapse under vacuum. Keep connections tight to avoid air leaks. A foot valve helps prime and hold water. Prime the pump before starting, and do not run it dry. A strainer protects the pump from debris.
Water source and quality
Surface water carries sand, weeds and debris, which can damage pumps. Use screens and filters. Wells may carry sand, which wears pumps. Check source capacity so you do not pump it dry. Check water rights and permits. Rules differ by state; check your state water agency.
Power and fuel
Electric pumps need correct voltage, wiring and protection. Engine pumps need fuel, oil and ventilation. Estimate fuel use and plan deliveries. Keep fuel storage safe. PTO pumps need suitable tractors and shielding. See utility tractor rentals: sizing guide.
A word from the farm radio
Watching a pump fill a field is quiet work, and a little ag talk helps the hours pass. Try farm.fm for farm news and conversation while the sprinklers run. It will not lower your head loss, but it does improve the time between pump checks, and the corn has never objected to the playlist.
Common mistakes to avoid
- Undersized pump.
- Too much suction lift.
- Air leaks.
- Running dry.
- Ignoring water rules.
Inspect before you accept
Check the casing, impeller, seals, hoses, fittings, engine or motor and wiring. Test run if possible. Photograph existing damage. See understanding rental equipment condition reports.
Safety
- Lock out electric or PTO power before service. See the farm machinery lockout-tagout procedure template.
- Keep PTO shields in place. See the PTO safety shield inspection form.
- Keep cords dry and use ground-fault protection.
- Ventilate engines.
- Secure hoses, since pressure can whip them.
- Keep children away from water sources.
See the OSHA agricultural operations page.
Transport
Pumps can be heavy. Secure for travel. See the equipment transport tie-down checklist.
Costs and terms
Ask about daily and weekly rates, fuel, delivery and deposit. See how to budget for farm equipment rentals and understanding rental agreements.
Planning the setup
Walk the system and measure distances and elevation. Choose pump and hoses. Plan power or fuel. Test with water before the crop needs it. Plan checks every few hours. Keep spare fittings and tools.
Troubleshooting
If the pump will not prime, check air leaks and foot valve. If flow is low, check strainers and impeller. If pressure is low, check pipe size and leaks. If the engine overheats, check cooling. Contact the dealer when unsure.
Cleaning and return
Drain the pump, flush with clean water, dry and wipe down. See returning farm equipment: cleaning and fuel rules.
A sample job
A vegetable grower rents a diesel centrifugal pump to draw water from a pond during a dry spell. The dealer sizes the pump from field flow and head, and the grower uses screens and a foot valve. Water flows steadily, and the pump is flushed and returned.
Questions to ask the dealer
- What flow and head can it deliver?
- What suction lift does it handle?
- What fuel or power does it need?
- What are the cleaning requirements?
- Can the dealer help size my system?
Keeping records
Record dates, hours, fuel and water pumped. See record keeping for farm equipment rentals.
Water rights and reporting
Water belongs to the state in many places, and using it can require permits, reporting or limits. Ask your state water agency whether your source is covered and what records you need. Do not pump from streams, ditches or neighbors' ponds without permission. Fines can be large, and drought rules can change quickly. Keep copies of permits with the pump.
Energy cost and efficiency
Pumping energy is a major irrigation cost. A pump that runs far from its best efficiency point wastes fuel. Ask the dealer for a pump curve and run the pump near the peak. Use right-sized pipe to reduce friction loss, and fix leaks. Water at night or early morning in hot climates to cut evaporation. Track fuel per acre-inch so you can compare options.
Winterizing and storage
If the pump will be idle in cold weather, drain it fully to prevent freeze damage. Remove hoses, dry them and coil them off the ground. Protect engines and electric parts from moisture. Ask the dealer to show you how to drain and store the unit, and return it clean so the next customer can use it without surprises.
Bottom line
Pick a pump by flow, head and lift, then match hoses, power and water rules. A well-sized pump saves fuel and water.
Frequently asked questions
How do I size a pump?
Add system flow and head, then check the pump curve.
What is suction lift?
How high the pump must pull water from the source.
Do I need a permit to pump water?
Often yes. Check with your state water agency.
Can I run a pump dry?
No. It can destroy seals and impellers.