Farm Equipment Rentals
Irrigation and Water Equipment Rentals

Renting a Water Meter for Flow Testing

Rent a water meter or flow tester to check well output, pump performance and irrigation uniformity: meter types, accuracy, installation, readings, records and common errors.

5 min read1,079 wordsUpdated November 2026
Renting a Water Meter for Flow Testing: illustration of a center pivot and a diesel pump at a pond

Water flow is hard to judge by eye. A rented meter or flow tester gives actual numbers for pump output, well tests and irrigation checks. Farms use them to check pump wear, find leaks, set irrigation schedules and report water use. This guide covers meter types, setup and reading.

Why measure flow

  • Pump check. Compare output with rated curves.
  • Leak finding. Flow that does not match expected use hints at leaks.
  • Irrigation scheduling. Apply the right depth.
  • Compliance. Some water districts require measurement.
  • Well testing. Know sustainable yield.

See SARE publications, USDA NRCS and your state page.

Types of meters

  • Propeller or turbine meters. Common in-line models.
  • Magnetic meters. No moving parts, good for dirty water.
  • Ultrasonic clamp-on meters. Clamp onto the outside of the pipe, no cutting.
  • Orifice or venturi devices. Simple and rugged.
  • Portable test meters. For spot checks.

Clamp-on meters are handy for rentals because they do not require cutting the pipe.

Renting a Water Meter for Flow Testing: illustration of a center pivot and a diesel pump at a pond
Illustration: a center pivot and a diesel pump at a pond. Original artwork for Farm Equipment Rentals.

Matching the meter to the job

Check pipe size, material, flow range and pressure. Ask about accuracy and the straight pipe length required upstream and downstream. Ask whether the meter reads flow rate, total volume or both. Confirm power needs.

Installation

For in-line meters, install in a straight pipe run with the pipe full of water. Avoid placing them near elbows, valves or pumps. For clamp-on meters, clean the pipe surface and enter pipe data. Use coupling gel as directed. Check for air bubbles that cause errors.

Taking readings

Record flow rate and totalizer readings at set times. Note pump settings, pressure and conditions. Repeat checks to confirm. Compare readings with pump curves and sprinkler specifications. See irrigation pump rentals: types and sizing.

Interpreting results

Low flow may mean wear, clogs or leaks. High flow may mean a broken line. Compare readings across zones for uniformity. Log trends. A drop over time can warn of pump wear.

Common mistakes to avoid

  • Poor straight pipe length.
  • Pipes not full.
  • Dirty sensor surfaces.
  • Wrong pipe data.
  • No records.

Inspect before you accept

Check the display, sensors, cables, batteries and calibration certificate if offered. Test on a known flow. Photograph existing damage. See understanding rental equipment condition reports.

Safety

See the OSHA agricultural operations page.

Transport

Meters are delicate. Carry them in padded cases. See the equipment transport tie-down checklist.

Costs and terms

Ask about daily and weekly rates, deposit and damage terms. See how to budget for farm equipment rentals and understanding rental agreements.

Planning the test

Choose the day, pump settings and zones to test. Gather pipe data, pump specifications and past readings. Plan to test at several flow settings. Take notes and photos.

Troubleshooting

If readings are erratic, check air bubbles and pipe fullness. If the display is blank, check power. If flow seems wrong, check pipe data and sensor placement. Contact the dealer when unsure.

Using results

Compare measured flow with your pump's curve to see wear. Check sprinkler or pivot output against design flows. Adjust schedules to match actual output. See renting a soil moisture probe for scheduling.

Cleaning and return

Clean sensors and cables, dry the case and return all accessories. See returning farm equipment: cleaning and fuel rules.

A sample job

A grower rents a clamp-on ultrasonic meter to test a pivot's pump after yields lagged. The reading shows flow well below the rated curve. The grower repairs a worn impeller, retests and logs improvement.

Questions to ask the dealer

  1. What pipe sizes and flows does it cover?
  2. What accuracy can I expect?
  3. Does it log data?
  4. What setup help is offered?
  5. What damage terms apply?

Reporting and rights

Some districts require meters and reports of water use. Ask your water district or NRCS office about requirements, and keep records for audits.

Keeping records

Record dates, readings, pump settings and results. See record keeping for farm equipment rentals.

Running a pump test

To test a pump, record pressure at the pump and at the field, then record flow at the same time. Run the test at several valve settings, from nearly closed to fully open, to see the real pump curve. Compare against the manufacturer's curve to judge wear. Do the test at normal operating conditions, with the same hoses and fittings as in use.

Testing sprinkler and pivot output

For sprinklers, compare total flow with the sum of nozzle flows. A big difference suggests leaks, worn nozzles or wrong sizes. For pivots, test with the system running at normal speed and check pressure at the pivot point and the end. Uniformity affects yield.

Checking wells

Well tests measure how drawdown changes with pumping rate. Run the pump at a steady rate for several hours and record water level and flow. This helps you set safe pumping rates and avoid damaging the pump or aquifer. Ask your extension or well contractor for guidance.

Calibration and accuracy

No meter is perfect. Ask the dealer for the stated accuracy and whether it has been checked recently. Compare with a known volume, such as filling a tank of known size, if you need confidence in the numbers.

Documenting the test

Take photos of the meter setup, record pipe sizes and note weather and pump settings. Save the readings in a spreadsheet. A good record helps you compare year to year and shows regulators or lenders that your system is maintained.

Using flow data with energy bills

Combine flow readings with your electric or fuel use to compute the cost per acre-inch of water. A jump in cost per acre-inch suggests pump wear or system problems. Sharing results with your power company or extension office can unlock efficiency programs.

Rentals versus buying

If you test only once or twice a year, renting is cheaper than owning a meter. If you need continuous records for compliance, a permanent meter may be better. Ask the dealer about rent-to-own options.

Bottom line

A flow meter shows what your system really delivers. Choose the right type, install carefully and log readings.

Frequently asked questions

What is the easiest meter to rent?

Clamp-on ultrasonic meters, because they need no pipe cutting.

Do I need straight pipe?

Yes. Follow the meter's guidance.

Can it find leaks?

Readings help show unexpected flow.

Is it accurate?

It depends on setup and the meter. Ask the dealer.

Keep reading

Irrigation and Water Equipment Rentals

Renting a Sprinkler System for Pasture

Rent a sprinkler system for pasture and hay ground: hand-line, wheel-line and big-gun options, mainline, pumps, spacing, pressure, setup labor, wind, safety and costs.

Irrigation and Water Equipment Rentals

Renting a Trash Pump for Dirty Water

Rent a trash pump for muddy, debris-laden water in ponds, pits and ditches: solids size, impeller type, engine, hoses, priming, safety, clogs and cleaning after use.

Irrigation and Water Equipment Rentals

Renting a Misting System for Livestock Cooling

Rent a misting system to cool livestock in hot weather: nozzles, pumps, pressure, timers, humidity limits, placement, water quality, safety and cleaning after the season.

Irrigation and Water Equipment Rentals

Renting a Cistern for Water Storage

Rent a cistern or storage tank for farm water: tank sizes, materials, placement, filling, pumps, freeze and algae control, livestock and irrigation use, safety and costs.