Farm Equipment Rentals
Irrigation and Water Equipment Rentals

Renting a Pipe Puller for Irrigation Repair

Rent a pipe puller or pipe plow to install or repair irrigation lines: types, tractor needs, depth, pipe sizes, locates, fittings, pressure tests, safety and costs.

5 min read1,050 wordsUpdated November 2026
Renting a Pipe Puller for Irrigation Repair: illustration of a center pivot and a diesel pump at a pond

Irrigation systems break: pipes crack, fittings leak and mainlines get nicked by equipment. A pipe puller, also called a pipe plow or cable plow, pulls flexible pipe through the soil without an open trench. It is fast for new runs and some repairs. This guide helps you decide if it fits and how to use it safely.

What a pipe puller is

A pipe puller is a blade or shank attached to a tractor or skid steer. It opens a narrow slot in the soil while feeding pipe or cable into it. It works with polyethylene and other flexible pipes. Rigid pipe usually needs a trench. See renting a trencher for water lines.

When to choose a puller

  • Long, straight runs. Faster than trenching.
  • Flexible pipe. Poly lines fit well.
  • Soft soils. Fewer rocks.
  • Quick fixes. Replacing a damaged section by running a new line.

If the soil is rocky or full of roots, a trencher or excavator may work better.

Renting a Pipe Puller for Irrigation Repair: illustration of a center pivot and a diesel pump at a pond
Illustration: a center pivot and a diesel pump at a pond. Original artwork for Farm Equipment Rentals.

Tractor and hitch needs

Pullers need considerable power. Check horsepower, hitch type and weight. Make sure the tractor can hold a straight line and has enough traction. See compact tractor rentals for small farms, utility tractor rentals: sizing guide and renting a tractor with front-end loader.

Depth and pipe size

Depth depends on frost, traffic and local codes. Ask the dealer about the maximum depth and pipe diameter. Deeper runs need more power. See SARE publications, USDA NRCS and your state page.

Locates and tile

Call 811 before plowing. Map drain tile, septic lines, wells and old irrigation lines. Plowing through tile damages drainage. Mark the route with flags. Use farm maps and past records.

Repairing a damaged line

Find the break by tracing wet spots or using flow tests. See renting a water meter for flow testing. For short breaks, excavate and replace the section with couplings. For long damage, plow in a new line and connect it.

Fittings and joints

Use fittings rated for pipe and pressure. Insert stiffeners where required. Clean pipe ends, and follow instructions for clamps or compression fittings. Keep dirt out of the pipe.

Common mistakes to avoid

  • Skipping locates.
  • Wrong depth.
  • Pipe kinked on entry.
  • No pressure test.
  • Pulling too fast.

Inspect before you accept

Check the blade, shank, mounts, pins and hydraulics. Test with the tractor. Photograph existing damage. See understanding rental equipment condition reports.

Safety

See the OSHA agricultural operations page and CDC NIOSH agriculture.

Transport

Pullers can be heavy and awkward. Secure them. See the equipment transport tie-down checklist.

Costs and terms

Ask about daily and weekly rates, delivery and deposit. See how to budget for farm equipment rentals and understanding rental agreements.

Planning the job

Walk the route and stake it. Unroll pipe along the route to relax coils. Plan the order of work, and have fittings and tools ready. Check soil moisture, because very dry or wet soils behave badly.

Troubleshooting

If the blade will not go deep, check soil, power and angle. If the pipe kinks, adjust feed. If the tractor spins, reduce depth or add weight. See the tractor ballast weighting guide. Contact the dealer when unsure.

Cleaning and return

Remove soil and plant material, grease fittings and refuel if required. See returning farm equipment: cleaning and fuel rules.

A sample job

A vegetable farm rents a pipe plow to replace a damaged mainline section with a new poly line. The crew calls 811, plows the new line, connects it and pressure tests. The plow is cleaned and returned.

Questions to ask the dealer

  1. What pipe sizes and depth does it handle?
  2. What tractor does it need?
  3. Can I rent fittings and tools?
  4. What are cleaning requirements?
  5. What damage terms apply?

Insurance and liability

Ask whether your policy covers rented machinery and damage to buried lines. Keep locate tickets and photos.

Keeping records

Record the new route, depth and pipe type. See record keeping for farm equipment rentals.

Soil conditions and timing

Moist but not saturated soil works best. Very dry, hard ground resists the blade and wears equipment, while saturated soil can smear and collapse. Avoid plowing when frost is in the ground. If the soil is full of rocks, test a short stretch first so you know what to expect.

Pipe handling

Unroll pipe along the route on a warm day so it relaxes, and avoid sharp bends at the feed. Protect pipe from sharp edges and from sun damage before installation. Cap the ends to keep out dirt and animals. Leave a little slack to allow for settling and temperature changes.

Marking and records after plowing

Mark the route with stakes and photos, and measure to fixed landmarks. Update your farm map with depth and pipe size. Good records prevent accidents later when someone digs or tills the same area.

Alternatives for tricky spots

Rocky, rooty or very hard soils may defeat a plow. Consider a trencher, an excavator or directional boring instead. Roads and drives usually need a bore or sleeve. Your dealer can suggest the best tool for each crossing.

Keeping spare parts on hand

Carry spare couplings, clamps, pipe tape and a hacksaw or pipe cutter. A single missing fitting can stop a repair for a day. Check that fittings match the pipe's outside diameter and pressure rating before you leave the shop.

Working with a helper

Two people make pipe plowing safer and faster, one on the tractor and one watching the pipe feed. Agree on hand signals before starting. See the hand signal guide for farm equipment.

Bottom line

Pipe pullers lay or replace flexible lines quickly in suitable soils. Locate lines first, match power, test and record the route.

Frequently asked questions

What pipe works with a puller?

Flexible pipe such as polyethylene.

Can it handle rocks?

Poorly. Rocky soils may need a trencher.

How deep can I go?

It depends on the unit and tractor. Ask the dealer.

Do I need locates?

Yes. Call 811 in the United States.

Keep reading

Irrigation and Water Equipment Rentals

Renting a Soil Moisture Probe for Scheduling

Rent soil moisture probes and sensors for irrigation scheduling: probe types, installation depth, calibration, reading charts, data loggers, mistakes and how to use results.

Irrigation and Water Equipment Rentals

Renting a Ditch Digger for Irrigation Lines

Rent a ditch digger for irrigation lines: trencher types, depth and width, soil and rock limits, utility locates, pipe bedding, backfill, safety, transport and costs.

Irrigation and Water Equipment Rentals

Irrigation Pump Rentals: Types and Sizing

Rent an irrigation pump sized right: centrifugal, submersible and PTO types, flow and head, suction lift, fuel or power, hoses, priming, filtration, safety and water rights.

Irrigation and Water Equipment Rentals

Renting a Water Chiller for Livestock

Rent a water chiller to cool livestock drinking water in hot weather: chiller types, capacity, plumbing, power, insulation, cleaning, intake effects, safety and costs.