Farm Equipment Rentals
Irrigation and Water Equipment Rentals

Renting a Soil Moisture Probe for Scheduling

Rent soil moisture probes and sensors for irrigation scheduling: probe types, installation depth, calibration, reading charts, data loggers, mistakes and how to use results.

5 min read1,074 wordsUpdated November 2026
Renting a Soil Moisture Probe for Scheduling: illustration of a center pivot and a diesel pump at a pond

Irrigation based on a calendar can waste water or stress crops. Soil moisture probes measure how wet the root zone is, so you can irrigate when needed. Rentals let you test sensors for a season or two before buying. This guide covers types, installation and how to use readings.

Why use probes

  • Save water and energy.
  • Avoid stress and disease.
  • Cut leaching of nutrients.
  • Improve yield and quality.

See SARE publications, USDA NRCS and your state page.

Types of sensors

  • Tensiometers. Measure soil water tension, how hard plants must work to extract water.
  • Capacitance probes. Measure volumetric water content with electronic sensors.
  • Resistance blocks. Cheap but less precise.
  • Neutron probes. Accurate but regulated and rare.
  • Handheld meters. Spot checks.

Choose by soil type, crop and need for continuous data.

Renting a Soil Moisture Probe for Scheduling: illustration of a center pivot and a diesel pump at a pond
Illustration: a center pivot and a diesel pump at a pond. Original artwork for Farm Equipment Rentals.

Where and how deep

Place sensors in representative spots, not wet low areas or dry knolls. Install at several depths, such as in the upper, middle and lower root zone. Shallow-rooted crops need shallower sensors. Make sure soil contacts the sensor tightly with no gaps. Mark locations with flags.

Installation

Follow the manufacturer's guidance. Use the right auger or tool to make a clean hole. Slurry or backfill carefully to avoid air pockets. Protect cables from equipment and animals. Keep tops above water.

Calibration

Sensors may read differently in sand, loam or clay. Calibrate to your soil using field capacity and wilting point. Ask the dealer or extension agent for help. Note how readings change after irrigation and rain.

Reading the data

Look for patterns. After irrigation, readings rise to field capacity and then decline as the crop uses water. Plan irrigation before readings reach the stress point. Compare depths to see where roots draw water. Keep notes on crop stage and weather.

Data loggers and telemetry

Loggers record readings over time. Some send data to phones or computers. Check battery life, memory and connectivity. Download data regularly. Telemetry can save trips but may add cost.

Common mistakes to avoid

  • Poor soil contact.
  • Single sensor locations.
  • No calibration.
  • Ignoring trends.
  • Letting batteries die.

Inspect before you accept

Check sensors, cables, readers and batteries. Test on known soil. Photograph existing damage. See understanding rental equipment condition reports.

Safety

  • Mark probe locations so tractors and tillage avoid them.
  • Watch for underground lines when digging.
  • Wear gloves and eye protection when augering.
  • Keep cables clear of equipment.

See the OSHA agricultural operations page.

Costs and terms

Ask about weekly and seasonal rates, loggers, replacement of lost sensors and deposit. See how to budget for farm equipment rentals and understanding rental agreements.

Planning the season

Install sensors before the first irrigation. Take readings at set times, such as mornings. Add weather data. See renting a weather station for irrigation decisions. Adjust schedules as the crop grows. Remove sensors before harvest or tillage.

Troubleshooting

If readings jump, check contact and cables. If a sensor reads constantly wet, check for water pooling. If it reads dry, check for gaps. If the logger stops, check batteries. Contact the dealer when unsure.

Working with irrigation systems

Combine probe data with system flow. See renting a water meter for flow testing. Match irrigation depth to what the soil can hold, avoiding runoff or deep percolation. For drip systems, sensors show how far water moves sideways and down.

Cleaning and return

Clean sensors, dry them and return all parts. See returning farm equipment: cleaning and fuel rules.

A sample season

A vegetable grower rents capacitance probes and a logger for a season. The grower installs sensors at three depths in two fields, irrigates when readings approach a set point and cuts water use. Sensors are cleaned and returned.

Questions to ask the dealer

  1. What sensor types suit my soil?
  2. What calibration help is offered?
  3. Does it log or send data?
  4. What battery life?
  5. What damage terms apply?

Keeping records

Record readings, irrigation dates and amounts, and crop stage. See record keeping for farm equipment rentals.

Understanding field capacity and stress points

Field capacity is the amount of water a soil holds after draining. The permanent wilting point is where plants can no longer extract water. Between them lies the available water. Most crops do best when you irrigate before half of the available water is used. Ask your extension agent for the numbers for your soil and crop.

Sandy versus clay soils

Sandy soils hold little water and dry fast, so you irrigate often with smaller amounts. Clay soils hold more water but release it slowly and drain poorly, so too much water can cause problems. Loams fall between. Your probe readings will look different in each, so calibrate carefully.

Combining sensors with weather and crop stage

Water use rises during rapid growth, flowering and fruit fill. Add weather data on temperature, wind and rain, and keep notes on crop stage. A few weeks of readings reveal how fast your crop uses water, and you can plan irrigation ahead.

Using sensor data to cut costs

Fewer irrigations save pumping energy and labor, and avoiding overwatering protects soil and water quality. Track hours pumped and compare with last year, so you can see whether sensors pay for themselves.

Training your crew

Show everyone who reads the probes how to take readings, record them and recognize unusual numbers. Agree on a simple chart or app, and decide who has authority to start or stop irrigation. Consistent habits matter more than fancy equipment.

When probes are not enough

Probes read the spot where they are installed, so they cannot catch every variation across a field. Combine them with walking the field, digging a small hole to feel the soil and watching the crop for stress. If readings and crop appearance disagree, trust the field and check the sensor.

Seasonal wrap-up

At season end, pull sensors before tillage, clean them and store them dry. Review your logs, note what worked and decide whether to buy, rent again or try other methods. Share what you learn with neighbors and your extension office.

Bottom line

Soil moisture probes make irrigation decisions based on data. Install carefully, calibrate, watch trends and adjust.

Frequently asked questions

Which probe is best?

It depends on soil, crop and budget. Ask the dealer.

How many sensors do I need?

Several depths in representative spots in each field.

Do I need to calibrate?

Yes, to your soil.

Can I use them with drip?

Yes, and they help show wetting patterns.

Keep reading

Irrigation and Water Equipment Rentals

Renting a Fertigation System for Nutrient Delivery

Rent a fertigation injector system to apply fertilizer through irrigation: injector types, tanks, mixing, backflow protection, rates, calibration, safety and cleanup.

Irrigation and Water Equipment Rentals

Renting a Pipe Puller for Irrigation Repair

Rent a pipe puller or pipe plow to install or repair irrigation lines: types, tractor needs, depth, pipe sizes, locates, fittings, pressure tests, safety and costs.

Irrigation and Water Equipment Rentals

Renting a Weather Station for Irrigation Decisions

Rent a weather station for irrigation decisions: sensors for rain, wind, temperature and humidity, evapotranspiration, siting, data loggers, calibration and using the data.

Irrigation and Water Equipment Rentals

Renting a Ditch Digger for Irrigation Lines

Rent a ditch digger for irrigation lines: trencher types, depth and width, soil and rock limits, utility locates, pipe bedding, backfill, safety, transport and costs.