Farm Equipment Rentals
Livestock and Hay Equipment Rentals

Renting a Hammer Mill for Feed Grinding

Rent a hammer mill to grind grain and forage: screen sizes, particle size, power and PTO, throughput, dust and fire control, hearing protection, safety and cleaning after use.

5 min read1,013 wordsUpdated November 2026
Renting a Hammer Mill for Feed Grinding: illustration of a livestock trailer and squeeze chute beside a hay barn

A hammer mill breaks grain, hay and other feed into smaller particles using fast-spinning hammers. It is a common way to process feed for livestock on farms that mix their own rations. Renting a mill lets you grind a season's feed or test equipment before buying. This guide covers types, setup and safe use.

How hammer mills work

Material enters a chamber where hammers on a spinning rotor strike it against a screen. Particles small enough to pass through the screen leave the chamber, and larger pieces are hit again. Screen hole size controls particle size. Mills may be PTO-driven, electric or engine-powered.

Compare with roller mill rentals for grain processing and renting a pellet mill for custom feed.

Screen and particle size

Different animals need different particle sizes. Fine grinding may increase digestibility for some animals but can cause digestive problems in others, such as acidosis in ruminants. Ask your nutritionist or extension office for recommendations. See SARE publications and your state page. Keep several screen sizes available, and test small batches.

Renting a Hammer Mill for Feed Grinding: illustration of a livestock trailer and squeeze chute beside a hay barn
Illustration: a livestock trailer and squeeze chute beside a hay barn. Original artwork for Farm Equipment Rentals.

Power and throughput

Check whether the mill uses PTO, electric or engine power. Match tractor horsepower or motor size to the mill. Throughput depends on grain type, moisture, screen size and power. Wet or oily material slows output and can clog screens. Dry grain grinds best.

Setting up

  1. Level, stable site. Vibration can loosen parts.
  2. Feed hopper and collection. Plan how grain gets in and how ground feed leaves.
  3. Dust control. Use an enclosed collection system or ventilation.
  4. Safe power connection. Follow electrical codes and PTO rules.
  5. Fire prevention. Keep area clear and have extinguishers.
  6. Magnets or screens to catch metal.

Run an empty test, then a small batch.

Quality and safety of feed

Inspect grain for mold and foreign objects before grinding. Moldy grain can cause health problems. Avoid grinding treated seed or chemicals. Store ground feed dry and use it within a safe time, since ground feed spoils faster than whole grain. Keep records for medicated feeds. See renting a feed bin for bulk storage.

Common mistakes to avoid

  • Grinding too fine.
  • Feeding metal into the mill.
  • Poor dust control.
  • Wet grain.
  • Skipping hammer checks.

Inspect before you accept

Check hammers, screens, rotor, bearings, belts, shields, hopper and motor or PTO. Run the mill empty. Photograph existing damage. See understanding rental equipment condition reports.

Safety

See the OSHA agricultural operations page and CDC NIOSH agriculture.

Transport

Mills are heavy and awkward. Use a trailer and tie-downs. See the equipment transport tie-down checklist.

Costs and terms

Ask about daily and weekly rates, delivery, screen sets, deposit and wear charges. See how to budget for farm equipment rentals and understanding rental agreements.

Planning the grinding day

Decide how much feed you need and where it will go. Prepare bins or bags. Check weather and power. Assign roles for feeding, bagging and housekeeping. Keep spare screens, hammers and tools. Keep records of batches.

Troubleshooting

If throughput is low, check screen, moisture and hammers. If the mill vibrates, stop and check hammers and bearings. If dust is heavy, improve collection. If screens clog, dry the grain. Contact the dealer when unsure.

Cleaning and return

Empty and brush out the chamber, clean screens and grease bearings. See returning farm equipment: cleaning and fuel rules.

A sample day

A small farm rents a PTO hammer mill to grind corn for hogs. The farmer picks a medium screen, runs a small test and bags the ground corn. Dust is controlled with ventilation, and the mill is cleaned and returned.

Questions to ask the dealer

  1. What screens are included?
  2. What power does it need?
  3. What throughput should I expect?
  4. What are the cleaning requirements?
  5. How do I handle dust?

Hearing and lung protection

Hammer mills are loud and dusty. Use hearing protection rated for the noise, and wear a respirator or dust mask for fine dust. Limit exposure time and take breaks. Keep dust from collecting on lights and motors. Dust that settles can burn or explode when stirred up, so clean surfaces regularly with a vacuum rather than blowing.

Keeping records

Record dates, batches, screens and repairs. See record keeping for farm equipment rentals.

Grinding for different animals

Swine and poultry often need finer grinding, while cattle and sheep usually need coarser feed to protect rumen health. Horses can be sensitive to dusty feed. If you mix several ingredients, grind them separately to control particle size, then blend. Check with your nutritionist about screen sizes for each species and test samples before committing to a full batch.

Setting up for dust and noise

Place the mill in a well-ventilated area away from animals and living spaces. Use a cyclone or dust collection bag if one is available. Place sound barriers or work at a distance when possible, and rotate people to limit exposure. Keep sources of ignition away, and make sure electrical equipment is rated for dusty areas.

Spare parts and wear

Hammers wear on the edges and can be flipped or replaced. Screens wear and tear. Carry a spare set, and check them each day. Record hours so you know when to replace parts. If the mill begins to vibrate or lose capacity, stop and inspect rather than pushing on.

Bottom line

A hammer mill gives control over particle size and cost. Match screens and power, control dust and noise, and never feed metal into the mill.

Frequently asked questions

What screen should I use?

It depends on the animal and feed. Ask a nutritionist.

Can I grind moist grain?

It clogs screens and slows output. Dry grain works best.

Is dust dangerous?

Yes. It can harm lungs and cause explosions if not controlled.

Can I grind hay?

Some mills can, with the right screens.

Keep reading

Livestock and Hay Equipment Rentals

Roller Mill Rentals for Grain Processing

Rent a roller mill to crack, crimp or flake grain: roll gap, corrugation, throughput, moisture, power, dust control, feed quality, safety, cleaning and when it beats grinding.

Livestock and Hay Equipment Rentals

Renting a Meat Grinder for On-Farm Processing

Rent a meat grinder for on-farm processing: plate sizes, throughput, cooling, sanitation, cross-contamination, local rules for sale, safety and cleaning steps.

Livestock and Hay Equipment Rentals

Renting a Grain Elevator Leg for Handling

Rent a grain elevator leg or bucket elevator to lift grain into bins: capacity, height, belt and bucket condition, drives, dust control, wiring, safety and cleaning after use.

Livestock and Hay Equipment Rentals

Renting a Hoof Trimming Chute for Cattle

Rent a hoof trimming chute for cattle: tilt tables vs lift chutes, restraints, setup, handling stress, hygiene, safety and cleaning, with tips on working with a trimmer.