Farm Equipment Rentals
Livestock and Hay Equipment Rentals

Renting a Pellet Mill for Custom Feed

Rent a pellet mill to make custom feed: die size, conditioning, moisture, binder, throughput, power, cooling, quality testing, dust control, safety and cleaning.

5 min read1,042 wordsUpdated November 2026
Renting a Pellet Mill for Custom Feed: illustration of a livestock trailer and squeeze chute beside a hay barn

Pellet mills compress ground feed through a die to form pellets. Pelleted feed reduces dust, sorting and waste, and it can be easier to store and handle. A rented pellet mill suits small feed producers, hobby farms and trials. This guide covers how mills work, how to run them and how to manage quality and safety. Always consult a nutritionist for rations.

How pellet mills work

Ground feed enters a conditioner where steam or moisture and heat are added. Rollers press the mixture through holes in a ring or flat die, and a knife cuts the strands into pellets. The pellets leave hot and soft, and they must be cooled and dried before storage.

See renting a hammer mill for feed grinding and roller mill rentals for grain processing for preparing ingredients.

Mill types

  • Flat die mills. Smaller, simpler and common for farm use.
  • Ring die mills. Higher capacity and used by commercial feed makers.
  • Electric or PTO powered. Check your power supply.

Ask the dealer about throughput and die sizes.

Renting a Pellet Mill for Custom Feed: illustration of a livestock trailer and squeeze chute beside a hay barn
Illustration: a livestock trailer and squeeze chute beside a hay barn. Original artwork for Farm Equipment Rentals.

Die size and ingredients

Die hole size sets pellet diameter. Smaller pellets suit chickens and rabbits, and larger ones suit cattle and horses. Ingredient mix affects pellet quality: fiber, fat, starch and moisture all matter. Too much fat reduces hardness. Not enough moisture or binder produces crumbly pellets. Work with a nutritionist, and run small test batches.

Moisture and binders

Moisture helps starch gelatinize and bind pellets. Too much moisture leads to poor flow and mold, and too little produces dust. Binders such as certain starches or molasses can improve hardness, but check that they are approved for your species. Follow feed regulations for your area; see your state page and the USDA APHIS for guidance.

Cooling and drying

Fresh pellets are hot and wet. Cool them with air, and spread them on screens or racks. Allow them to dry before storing. Pellets stored warm can sweat and grow mold. Test moisture and check pellet temperature before binning.

Quality testing

Check pellet length, hardness and durability. Drop a sample or crush it by hand. Sieve for fines. Adjust moisture, die or ingredient mix as needed. Record settings and results. See SARE publications.

Power and throughput

Check electrical needs and circuit capacity. Mills draw heavy loads at start. Throughput depends on die size, ingredients and moisture. Do not overload the motor.

Common mistakes to avoid

  • Wrong moisture.
  • Skipping cooling.
  • Mixing medicated and plain feed.
  • Overloading the mill.
  • Poor dust control.

Inspect before you accept

Check die, rollers, bearings, motor, belts, conditioner and guards. Run the mill empty. Photograph existing damage. See understanding rental equipment condition reports.

Safety

  • Lock out before servicing. See the farm machinery lockout-tagout procedure template.
  • Keep hands away from feed openings and rollers.
  • Wear hearing and respiratory protection.
  • Watch for hot surfaces and steam.
  • Control dust and ignition sources.

See the OSHA agricultural operations page and CDC NIOSH agriculture.

Transport

Mills are heavy. Use a trailer and tie-downs. See the equipment transport tie-down checklist.

Costs and terms

Ask about daily and weekly rates, delivery, die sets, deposit and wear charges. See how to budget for farm equipment rentals and understanding rental agreements.

Planning the run

Decide batch sizes and recipes. Prepare ground feed, bins and cooling space. Check power and weather. Assign roles. Keep spare dies and tools. Keep records of recipes, settings and results.

Troubleshooting

If pellets crumble, add moisture or binder. If the die plugs, check moisture and fat. If throughput is low, check die and rollers. If the motor trips, reduce feed rate. Contact the dealer when unsure.

Cleaning and return

Run a flush of clean feed, brush out the mill, clean the die and grease bearings. See returning farm equipment: cleaning and fuel rules.

A sample trial

A small poultry producer rents a flat die mill for a week to make layer pellets. The producer grinds ingredients, adds a small amount of moisture and tests pellet hardness. Pellets cool on screens before bagging. The producer cleans the mill and returns it.

Questions to ask the dealer

  1. What die sizes are included?
  2. What power does it need?
  3. What throughput should I expect?
  4. What are the cleaning requirements?
  5. Can the dealer help with setup?

Medicated feed and regulations

Medicated feeds are regulated, and you may need approvals, labeling and records. Do not make medicated feed without checking rules with your veterinarian and your state agency. Clean the mill thoroughly between medicated and non-medicated runs to avoid contamination. Keep batch records and label bags clearly.

Keeping records

Record dates, recipes, die size, settings and quality tests. See record keeping for farm equipment rentals.

Which animals benefit most

Pellets suit poultry, rabbits, swine, horses and some cattle and goats. They cut dust and prevent animals from picking out favorite pieces, which keeps nutrition balanced. For ruminants on forage diets, pelleted supplements work well, but pelleted hay or very fine pellets can change rumen function. Ask a nutritionist what pellet size and ingredients fit your animals, and watch intake and manure when you change feeds.

Planning batch size and storage

Pellets are best used within a reasonable time, since fat and vitamins can degrade. Plan batch size so you use the feed before it ages, and store it in clean, dry containers off the floor. Label bags with the date and recipe. Keep a small sample from each batch so you can check problems later.

Energy and cost

Pelleting takes electricity or fuel, labor and time. Compare the cost per ton with buying pelleted feed, including grinding, mixing, cooling and packaging. A small mill can make sense for specialty recipes or remote farms, but a bagged commercial pellet may be cheaper for ordinary rations. A one-week rental is a way to test the numbers before buying.

Bottom line

Pellet mills can produce uniform, low-waste feed when moisture, die and cooling are right. Test small batches, control dust and keep medicated and plain feed separate.

Frequently asked questions

Why make pellets?

They reduce waste, dust and sorting.

How do I cool pellets?

Use airflow or screens and let them dry before storage.

Do I need a binder?

Sometimes. Test with small batches.

Can I make medicated feed?

Only with proper approvals and records. Check local rules.

Keep reading

Livestock and Hay Equipment Rentals

Renting a Meat Grinder for On-Farm Processing

Rent a meat grinder for on-farm processing: plate sizes, throughput, cooling, sanitation, cross-contamination, local rules for sale, safety and cleaning steps.

Livestock and Hay Equipment Rentals

Renting a Grain Dryer for Harvest Moisture

Rent a grain dryer to reach safe storage moisture: batch, continuous and in-bin types, fuel, capacity, temperature, cooling, energy costs, monitoring, safety and set-up steps.

Livestock and Hay Equipment Rentals

Renting a Cattle Trailer for Transport

Rent a cattle trailer for hauling cattle safely: capacity, floors, gates, ventilation, loading flow, handling stress, tow vehicle ratings, paperwork, weather and costs.

Livestock and Hay Equipment Rentals

Renting a Shearing Stand for Sheep

Rent a shearing stand or tilt table for sheep: clean floors, lighting, electric handpieces, wool handling, animal comfort, shearer needs, safety, flock records and cleanup.