Elevator legs lift grain to the top of bins and bins and dryers. They move grain faster and gentler than long augers. Renting a leg works for farms adding capacity or handling a one-time harvest. This guide covers choosing a leg, setup and safe operation.
How a leg works
A belt with buckets runs inside a tall casing. Grain enters at the boot, rides up in buckets and discharges at the head into a spout or distributor. A motor and gearbox drive the head pulley. Legs can be freestanding or bolted to a structure.
See renting a grain auger for seed handling and renting a bagger for silage and grain for other handling tools.
Choosing capacity and height
Capacity is measured in bushels per hour. Match capacity to dryer, truck and bin rates so no part of the system waits. Height must reach your bins with spouting angles that allow flow. Ask for a leg that suits your tallest bin plus clearances.
Belt and buckets
Belts stretch and wear, and buckets can crack or loosen. Check:
- Belt alignment and tension.
- Splice condition.
- Bucket bolts and shape.
- Boot and head pulley lagging.
- Casing and joints. Look for leaks and sharp edges.
A worn belt can slip or tear and cause costly repairs.
Drives and wiring
Check motor size, voltage and starter. Have an electrician verify wiring, disconnects and grounding. Use proper conduit and dust-tight fittings. Include a emergency stop that is easy to reach. See renting a grain dryer for harvest moisture.
Dust, fire and explosion
Grain dust can explode. Control it with:
- Enclosed spouts and casings.
- Dust collection or ventilation.
- Regular cleanup with vacuums, not compressed air.
- No smoking, welding or open flames near the leg.
- Hot-bearing and misalignment sensors if available.
See the OSHA agricultural operations page and CDC NIOSH agriculture. Check your state page for regional resources.
Setup and foundation
Place the boot on a stable base and secure the leg with guy wires or bracing as required. Keep the area around the boot clean and dry. Provide access for trucks and hoppers. Use platforms and ladders with guards.
Common mistakes to avoid
- Mismatched capacity.
- Weak bracing.
- Ignoring belt tracking.
- Poor dust control.
- Skipping inspections.
Inspect before you accept
Check the belt, buckets, pulleys, bearings, casing, motor, gearbox, spouts and guards. Run the leg empty. Photograph existing damage. See understanding rental equipment condition reports.
Safety
- Lock out before inspecting. See the farm machinery lockout-tagout procedure template.
- Keep guards in place.
- Never enter a boot or bin while energized.
- Use fall protection on ladders and platforms.
- Keep people away from spouts.
Transport
Legs come in sections. Use proper trailers and securement. See DOT requirements for rented equipment transport and oversize load permits for rented equipment.
Costs and terms
Ask about daily and weekly rates, delivery, setup help and damage terms. See how to budget for farm equipment rentals and understanding rental agreements.
Planning the setup
Decide where the leg will go and how grain will flow. Plan electrical and foundations. Arrange crane or lift help for erection. Schedule inspections and cleaning. Keep spare belts, buckets and tools. Keep records of hours and issues.
Troubleshooting
If the belt slips, check tension and lagging. If it mistracks, adjust pulleys. If capacity is low, check buckets and speed. If it plugs, stop and clear. Contact the dealer when unsure.
Cleaning and return
Run out grain, clean the boot and casing and check the belt. See returning farm equipment: cleaning and fuel rules.
A sample harvest
A farm rents a leg to fill a new bin. An electrician checks wiring, and the crew braces the leg with guy wires. Grain moves quickly, and dust is controlled with ventilation. The leg is cleaned and returned.
Questions to ask the dealer
- What capacity and height?
- What drive and wiring does it need?
- What bracing is required?
- What are the cleaning requirements?
- Can the dealer help with setup?
Working with an electrician and a crane
Elevator legs are tall, heavy and electrical. Hire an electrician for the motor and starter, and a crane or lift operator for erecting long sections. Check permits and local codes. Verify overhead clearances and power lines before lifting anything. Have a written plan and safety briefing before work begins.
Keeping records
Record dates, hours, inspections and repairs. See record keeping for farm equipment rentals.
Matching the leg to the whole system
A leg is only one link. If trucks dump slower than the leg lifts, the leg waits, and if the dryer or bin cannot take grain as fast as the leg delivers, grain piles up. Write down the rate of each machine in bushels per hour, and plan around the slowest one. Check the receiving pit, hopper and spout sizes so grain flows without bridging. A short planning session avoids a bottleneck at harvest.
Belt tracking and tension
A belt that wanders rubs the casing and wears fast. Check tracking with the leg empty, and adjust the head or boot pulley in small steps. Keep tension firm but not tight, since too much tension strains bearings. After a few hours of use, recheck tension and bucket bolts. A quick check each morning catches problems before they stop the harvest.
Weather and wind
Tall legs catch wind, and ice or snow can add weight and slip hazards. Check guy wires before storms and after windy days. Do not work on the leg in high winds or lightning. Cover motors and controls from rain and snow, and keep ladders clear of ice. If storms are forecast, ask the dealer what steps protect the leg.
Bottom line
A rented leg lifts grain fast when capacity, belt, wiring and dust control are right. Inspect often and lock out before touching anything.
Frequently asked questions
Leg or auger?
Legs lift higher and gentler, and augers are simpler and portable.
Is dust a real risk?
Yes. Grain dust can ignite and explode.
Do I need bracing?
Yes, follow the manufacturer's requirements.
Can I run the leg empty?
Briefly for tests, but not for long.