An inspection is not paperwork for its own sake. It is the moment when you and the dealer agree on what condition the machine is in. Everything after, from repair bills to deposits to liability, leans on that record. This guide explains what inspections cover, how to run a good one and how to follow up.
Who inspects and when
Dealers inspect equipment before it goes out and when it comes back. You should inspect too, because your interests differ from theirs. Do it three times:
- At pickup, before you sign and before the machine leaves.
- During the rental, daily or at each shift.
- At return, with the dealer present.
Pickup inspection: a structured walk-around
Work around the machine in a consistent order so you do not miss anything.
Structure and body
Look for cracks, bent frames, damaged welds, dents and rust through. Check the hitch, drawbar, pins and clevis. Look at loader arms, booms and buckets for cracks near pivots.
Tires, tracks and wheels
Check pressure, tread, sidewalls, lug nuts and any bulges. Check track tension and wear on tracked machines.
Fluids and leaks
Look under the machine for drips. Check engine oil, coolant, hydraulic fluid and fuel. Note any leaks around cylinders, hoses and fittings.
Safety devices
Check the ROPS or cab, seatbelt, guards, PTO shields, steps, handrails, horn, backup alarm and lights. Missing or damaged safety devices are reason to refuse the machine. See the PTO safety shield inspection form.
Controls and gauges
Start the machine and check gauges, warning lights, steering, brakes and hydraulics. Run each control through its range slowly. Listen for unusual noises.
Attachments
Check implements, hoses, couplers, blades, chains and guards. Test hookup and drive.
For tractor-specific items, see the tractor daily pre-operation inspection checklist.
Run it, briefly
Ask to run the machine for a few minutes where possible. Operate the key functions, such as lifting a loader, engaging the PTO at idle or checking a pump at low flow. Many problems only show under load. If the dealer cannot allow a test, note that on the report.
Record what you find
Mark every flaw on the condition report. Take dated photos and short videos of each side, close-ups of any damage and the hour meter. Record fuel level. Get the dealer's signature and keep your copy. Do not accept "we'll note it later." See understanding rental equipment condition reports and documenting equipment condition before rental.
During the rental
Inspect before each shift. Check fluids, grease points, tires, belts, guards and hardware. Fix small things right away, and call the dealer for anything beyond routine care. Keep a short log. Stop work if a safety item fails. See three-point hitch maintenance checklist.
Return inspection
Return the equipment clean and fueled as the agreement requires. Be there for the dealer's inspection. Take new photos and record the hour meter. Ask for a signed return report that notes condition. If the dealer finds new damage, compare it with your pickup records on the spot. See returning farm equipment: cleaning and fuel rules and renter's responsibility: damage vs normal wear.
Specialized inspections
Different machines need extra checks:
- Sprayers. Pump, nozzles, hoses, booms, tank cleanliness and rinse records. See renting a boom sprayer for field crops.
- Skid steers and loaders. Quick attach, lift cylinders, tires and bucket edge. See renting a skid steer: uses and rates.
- Trailers. Brakes, lights, tires, tie-down points and safety chains. See livestock trailer rentals: types and sizing.
- Pumps and irrigation. Seals, hoses, strainers and fuel systems. See irrigation pump rentals: types and sizing.
- Grain handling. Flighting, bearings, guards and electrical cords. See renting a grain auger for seed handling.
What to do when you find a problem
Tell the dealer, note it on the report and decide together: repair, swap the machine or adjust terms. Do not accept a "fix it as you go" arrangement for safety-critical items. If a swap is not possible, consider canceling.
Common mistakes to avoid
- Signing first and inspecting later.
- Skipping the run test.
- Ignoring missing guards or lights.
- Taking one blurry photo.
- Not being present at return inspection.
Safety
Inspect with the engine off and the key removed unless you are testing. Use lockout when working near moving parts. See the farm machinery lockout-tagout procedure template, the OSHA agricultural operations page and CDC NIOSH agriculture.
A short inspection kit
Bring a flashlight, gloves, a tire gauge, a small notebook, a phone for photos and a copy of the checklist. Wear closed shoes. A rag helps you check fluids and spot fresh leaks.
Transport check
Before leaving the yard, verify hitch pins, safety chains, lights and tie-downs. See the equipment transport tie-down checklist.
A sample case
A farmer picks up a utility tractor. The walk-around reveals a missing PTO shield. The dealer replaces it, and the report is updated. During a short test the farmer notices a slow hydraulic leak, which is noted too. At return, a dispute over a bent fender is settled by pickup photos.
Keeping records
Keep condition reports, photos and emails with the rental file. See record keeping for farm equipment rentals.
Inspecting electrical and hydraulic systems
Look at wiring harnesses for chafing, loose connectors and taped splices. Check batteries for corrosion and secure mounting. On hydraulic systems, inspect hoses for cracks, bulges and abrasion, and check quick couplers for leaks. Never use your hand to find a hydraulic leak, because pressurized fluid can penetrate skin. Use cardboard or a rag instead.
Learning the machine
Ask the dealer to demonstrate controls, warning lights and emergency stops, and to point to the operator's manual or a quick-start card. Confirm safe working loads, slope limits and PTO speeds. If you have never run this model, ask for a short training session and write down what was covered.
Bottom line
A careful inspection at pickup, during use and at return costs minutes and can save thousands. Record everything and refuse machines with missing safety devices.
Frequently asked questions
How long should a pickup inspection take?
Often 15 to 30 minutes for a tractor, longer for complex machines.
Can I refuse a machine?
Yes, if safety devices are missing or it does not match the agreement.
Should I take photos?
Yes. Dated photos and video are the strongest record.
Who signs the report?
Both you and the dealer. Keep a copy.