In flood and furrow irrigation, water travels across the field by gravity. If the field is uneven, water pools in low spots and runs short in high spots. Laser or GPS leveling smooths the surface to a planned grade, often within tenths of a foot. It is precise, expensive work, but it can save water and improve yields. This guide covers what you need, the steps and when to rent or hire.
What laser and GPS leveling are
Laser systems use a rotating laser transmitter on a mast, with a receiver on the scraper or blade. The receiver tells a hydraulic control system to raise or lower the blade to keep it at the set grade. GPS systems use satellite positioning and a field design to drive the blade height without a laser. Both use a scraper or land plane pulled by a tractor, and both need a survey and plan.
For general leveling, see land leveling equipment rentals.
Why level for irrigation
- Uniform water advance. Water covers the field evenly.
- Less runoff and deep percolation. Less water lost.
- Better fertilizer use. Less leaching in low spots.
- More uniform crop growth.
- Reduced labor. Less need to move siphon tubes and gates.
Water savings and yield gains vary by field and system, and results depend on soil, crop and management. Ask your local NRCS office or extension agent about expected benefits and cost-share programs; see the USDA NRCS, the Farmers.gov service center locator and your state page.
Steps in a leveling job
- Survey. Collect field elevations on a grid, using a transit, laser or GPS.
- Design. Choose a grade, slope and direction suited to the soil and irrigation method. Compute cut and fill volumes.
- Prepare the field. Remove crops, rocks and obstructions, and locate tile and utilities.
- Strip topsoil if recommended, especially in deep cuts.
- Set up the laser or GPS and calibrate the receiver.
- Move soil. Use a scraper to cut from high areas and fill low areas, working to the design.
- Finish. Use a land plane or finishing blade for final smoothing.
- Check and verify. Resurvey, and fix any spots outside tolerance.
- Restore topsoil and fertility.
Expect the job to take days to weeks, depending on size.
Equipment you will need
- Scraper or leveling bucket suited to your soil volume.
- A powerful tractor, often four-wheel drive or tracked. See four-wheel-drive tractor rentals for heavy work.
- Laser transmitter and receiver, or GPS base station and rover.
- Hydraulic control kit to move the blade automatically.
- Survey tools if not included.
- A land plane for finishing.
Ask whether the rental includes training and support, because setup is technical.
Rent or hire?
Many farms hire a leveling contractor because the work needs experience, calibrated equipment and a design. Renting works well for small jobs, touch-ups or farmers who already have the skills. Compare:
- Rental cost for equipment, technology and delivery.
- Your labor and tractor time.
- Risk of mistakes, such as wrong grades or scalped topsoil.
- Contractor price, which may include design and warranty.
See how to budget for farm equipment rentals and the rental vs custom hire calculator.
Topsoil and fertility
Cutting high spots exposes subsoil that may be low in organic matter and nutrients. Where cuts are deep, strip and replace topsoil. After leveling, take soil samples and apply amendments as recommended. Plant a forgiving crop or a cover crop first to rebuild the area. See lime spreader rentals for soil pH correction and fertilizer spreader rentals: dry and liquid.
Weather and timing
Level when soil is firm and the field is clear, often after harvest or before planting. Avoid wet soil and heavy rain. Book early, because crews and equipment are busy in the dry season. See seasonal rental planning and how weather affects rental bookings and fees.
Common mistakes to avoid
- Skipping the survey. Without data, design is guesswork.
- Burying topsoil. Yields suffer.
- Poor laser setup. Wind, vibration and a bad mast position throw grades off.
- Ignoring tolerances. Small errors matter in irrigation.
- Forgetting outlets. Tailwater and drainage need places to go.
Inspect before you accept
Check the scraper cutting edge, hydraulics, hoses, frame, hitch and wheels. Test the laser or GPS on a short stretch. Photograph existing damage. See understanding rental equipment condition reports.
Safety
- Keep people away from scrapers and moving soil.
- Never walk under raised equipment without supports.
- Laser transmitters can harm eyes. Follow manufacturer rules and avoid looking into the beam.
- Use seatbelts and rollover protection. See the tractor rollover prevention checklist.
- Shut down before servicing. See the farm machinery lockout-tagout procedure template.
See the OSHA agricultural operations page.
A sample job
A farmer with a forty-acre field of row crops irrigated by furrows hires a surveyor, gets a design and rents a scraper with a laser system and a large tractor. After stripping and replacing topsoil in two cuts, the farmer finishes with a land plane and resurveys. The next season, water reaches the end of the rows more evenly, and the farmer shortens irrigation sets.
Questions to ask the owner
- Is the laser or GPS system calibrated, and when was it last serviced?
- Does the rental include training or phone support?
- What scraper size matches my tractor?
- Who supplies the survey equipment?
- What happens if wind or dust makes the laser unusable?
Measuring success
After leveling, resurvey and compare to the design. Then watch the first irrigation closely: time how long water takes to reach the end of the field, note any ponding and adjust set times. Keep notes so you can show results to a cost-share office or lender.
Bottom line
Laser leveling is a precision job that needs a survey, a design and capable equipment. Protect topsoil, check tolerances and compare rental with hiring an experienced crew before you commit.
Frequently asked questions
How precise is laser leveling?
Systems can hold grades within a fraction of a foot, but results depend on setup, soil and operator skill.
Does leveling save irrigation water?
Often it improves uniformity and can reduce water use, but savings vary by field and management.
Should I rent equipment or hire a contractor?
Contractors bring design and experience, and renting suits smaller jobs or experienced operators. Compare total cost and risk.
Is GPS leveling better than laser?
Both can work. GPS avoids laser line-of-sight limits, and costs and field size may favor one over the other.