Farm Equipment Rentals
Harvesting Equipment Rentals

Hay Rake Rentals: Wheel and Rotary

Rent a wheel or rotary hay rake: windrow forming, merging, raking speed, leaf loss, tractor needs, ground conditions, setup, safety and a plan to keep hay moving to the baler.

5 min read1,054 wordsUpdated November 2026
Hay Rake Rentals: Wheel and Rotary: illustration of a combine unloading grain into a cart

A hay rake collects cut hay into windrows and turns it so it dries. The right rake improves drying, protects leaves and makes the baler's job easier. Renting a rake works well for a few cuttings per season. This guide compares wheel and rotary rakes, settings, tractor needs and safety.

What rakes do

Raking turns and gathers hay, moves it off wet ground and merges rows into windrows suited to the baler. It can also fluff a heavy windrow to speed drying. The aim is a loose, uniform windrow with little leaf loss and little dirt.

Compare with tedder rentals for hay drying and renting a swather for hay and grain.

Wheel rakes

Wheel rakes use a series of ground-driven wheels with tines that roll hay into a windrow.

  • Simple and affordable.
  • Low power needs.
  • Gentle on many crops.
  • Slower at higher speeds.
  • Good for small fields.
Hay Rake Rentals: Wheel and Rotary: illustration of a combine unloading grain into a cart
Illustration: a combine unloading grain into a cart. Original artwork for Farm Equipment Rentals.

Rotary rakes

Rotary rakes use rotating tine arms to gather hay.

  • Fast and efficient.
  • Gentle on leaves when set properly.
  • Better at merging multiple swaths.
  • Higher cost.
  • Need more tractor power.

See SARE publications and your state page for hay quality guidance.

Choosing by situation

  1. Field size. Small fields suit wheel rakes, and large fields suit rotary rakes.
  2. Crop. Leafy crops like alfalfa benefit from gentle raking.
  3. Terrain. Rolling ground affects performance and tine height.
  4. Baler type. Match windrow width to the pickup.
  5. Tractor. Check horsepower, hitch and hydraulics.
  6. Weather. Rakes can speed drying, but raking too dry shatters leaves.

Settings

  • Tine height. Close to the ground without scraping soil.
  • Ground speed. Slower for leafy crops.
  • Windrow width. Match to the baler.
  • Wheel angle (wheel rakes). Adjust for windrow shape.
  • Rotor speed (rotary rakes). Follow the manual.

Check results after the first pass and adjust.

Timing

Rake when hay is moist enough that leaves hold on, usually in the morning with some dew, depending on crop and forecast. Do not rake too dry. Check moisture before baling and consult local guidance.

Tractor needs

Rakes need appropriate horsepower, PTO or hydraulics, and hitch. Rotary rakes may need hydraulics or PTO. See utility tractor rentals: sizing guide and compact tractor rentals for small farms.

Common mistakes to avoid

  • Raking too dry. Leaf loss.
  • Tines too low. Soil in hay.
  • Going too fast.
  • Ignoring baler needs.
  • Skipping the walkaround.

Inspect before you accept

Check tines, wheels, bearings, arms, hitch, hydraulics, shields and tires. Test the controls. Photograph existing damage. See understanding rental equipment condition reports.

Safety

See the OSHA agricultural operations page.

Transport

Rakes fold or lift for travel. Check lights, width and road rules. See DOT requirements for rented equipment transport.

Costs and terms

Ask about daily and weekly rates, delivery, deposit and wear charges. See how to budget for farm equipment rentals and understanding rental agreements.

Planning the raking pass

Walk the field before you start. Check windrow size, hay moisture and weather. Decide on a pattern that keeps windrows consistent, with extra care at the field edge and around obstacles. If you plan to merge rows, rake in a direction that suits the baler. Coordinate with the baler operator so raking stays ahead but not far enough that hay sits in rain.

Troubleshooting

If windrows look ropey, check speed and tine height. If leaves shatter, slow down or wait for more dew. If soil appears in hay, raise the rake. If the rake pulls to one side, check tire pressure and hitch alignment.

Cleaning and return

Clear hay from tines, grease fittings and wash off mud. See returning farm equipment: cleaning and fuel rules.

A sample job

A farm with 60 acres of alfalfa rents a rotary rake. The farmer rakes two swaths into one windrow in the morning, sets tine height just above the soil and drives at a moderate speed. The baler follows that afternoon, and leaf loss stays low.

Questions to ask the dealer

  1. What windrow widths does this rake make?
  2. What tractor do you recommend?
  3. What wear parts should I check?
  4. What are the return requirements?
  5. Can you provide settings guidance?

Keeping records

Record dates, fields, settings, weather and results. See record keeping for farm equipment rentals.

Merging windrows for the baler

Many balers work best with windrows of a particular size. Merge two or three swaths into one when the crop is light, and leave single windrows when it is heavy. Make windrows loose enough to let air through but tight enough to feed the pickup evenly. A rotary rake with a center delivery can merge several swaths in one pass, and a wheel rake may need two passes. Check the baler's recommended windrow width and match it as closely as you can.

Raking different crops

Alfalfa and clover lose leaves easily, so rake with extra care and at moisture levels that hold leaves on. Grass hay is more forgiving, though overdrying still wastes yield. Mixed stands fall in between. Heavy first cuttings may need fluffing before raking. Wet spots can slow drying, so rake those sections first or leave them for a second pass. Adjust speed and tine height to the crop and ground rather than treating every field the same way.

Ground conditions

Rocks, ruts and gopher mounds wreck tines and slow the job. Walk the field first and mark hazards, and fill or avoid deep holes. Wet ground makes rakes pick up soil, so wait if the surface is soft. On slopes, rake across the grade only if the rake and tractor are stable, and otherwise rake up and down with care.

Bottom line

Choose a wheel or rotary rake by field size, crop and tractor. Set height and speed to protect leaves and keep soil out of hay.

Frequently asked questions

Wheel or rotary rake?

Wheel rakes are simple and affordable, and rotary rakes are fast and efficient. Choose by field size.

When should I rake?

When hay is moist enough to hold leaves, according to local guidance.

How do I avoid soil in hay?

Keep tines above the ground and slow down.

What windrow width should I make?

Match the baler pickup width.

Keep reading

Harvesting Equipment Rentals

Tedder Rentals for Hay Drying

Rent a tedder to fluff and spread cut hay for faster drying: rotor types, timing, speed, leaf loss, tractor needs, safety and fitting tedding with raking and baling.

Harvesting Equipment Rentals

Renting a Mower-Conditioner for Hay

Rent a mower-conditioner for hay: disc or sickle cutterbars, roll or flail conditioning, cutting height, drying, tractor needs, daily service, safety and a plan to the baler.

Harvesting Equipment Rentals

Disc Mower Rentals for Pasture and Hay

Rent a disc mower for pasture and hay: cutting width, drum or disc design, blade care, stones, speed, tractor needs, cutting height, safety and return checks.

Harvesting Equipment Rentals

Silage Bagger Rentals for Storage

Rent a silage bagger to store forage in plastic bags: bag sizes, loading, density, moisture, site prep, tractor needs, bag care, safety and costs versus bunkers.