Greenhouse pests, such as whiteflies, thrips and aphids, thrive in warm, humid air. Foggers distribute control products through the whole space, reaching plants a hand sprayer might miss. They also carry real risks of exposure and plant injury. This guide covers choosing, calculating and using a fogger safely.
Types of foggers
- Thermal foggers. Heat creates a dense fog or smoke. Fire risk is higher.
- ULV (ultra-low volume) cold foggers. Atomize liquid into fine droplets without heat.
- Electric foggers. Smaller spaces and lower volumes.
- Aerosol bombs. Single-use cans, limited control.
Compare with renting a mist blower for orchard spraying and renting a fogger for barn cooling.
Read the label
The label decides whether fogging is allowed, which crops and spaces it covers, the dose per volume, the re-entry interval and the protective equipment. Never fog with a product not labeled for fogging. See the EPA pesticides page and your state agriculture department. Some states require licensing. Keep records.
Calculating volume and dose
Measure the greenhouse length, width and average height. Multiply to get cubic feet. Divide by label units to find the amount of product. Add equipment output rate to estimate fogging time. Double-check math, since errors cause injury or poor control.
Preparing the space
Close vents and doors, shut off fans unless the label directs otherwise, and remove people and pets. Cover or move food crops that must not be exposed. Turn off pilot lights and ignition sources when using thermal foggers. Post warning signs at all entrances.
Application
Start at the far end and work toward the exit. Keep the fogger at a steady flow and aim away from plants close to the nozzle. Fog for the calculated time. Lock the doors afterward and wait for the re-entry period. Ventilate before reentering.
Plant injury risks
Some plants are sensitive. Fog during cool hours to reduce stress, and test on a few plants first. Avoid overdosing. Check label notes about sensitive species and stages. Keep humidity moderate to avoid disease.
Common mistakes to avoid
- Using unlabeled products.
- Wrong volume math.
- No ventilation after fogging.
- Ignition sources near thermal foggers.
- Ignoring re-entry intervals.
Inspect before you accept
Check the tank, pump, nozzle, heater, hoses and controls. Test with water if possible. Photograph existing damage. See understanding rental equipment condition reports.
Safety
- Wear respirators, goggles, gloves and coveralls as the label states.
- Never enter a fogged space until the re-entry interval has passed.
- Keep open flames and sparks away from thermal fog.
- Store chemicals safely.
- Lock out before service. See the farm machinery lockout-tagout procedure template.
- Keep a fire extinguisher nearby.
See the OSHA agricultural operations page and CDC NIOSH agriculture.
Costs and terms
Ask about daily and weekly rates, cleaning fees and deposit. See how to budget for farm equipment rentals and understanding rental agreements.
Planning the job
Check pest pressure through scouting and sticky cards. Choose products and timing. Plan to repeat treatments if the label allows. Avoid spraying when workers are present. Keep records.
Integrated pest management
Fogging is one tool. Combine it with scouting, sanitation, screens, beneficial insects and cultural practices. Overuse of one product can lead to resistance. Ask your extension specialist for greenhouse pest programs. See Extension and SARE publications.
Troubleshooting
If the fog is thin, check pressure and nozzle. If the fogger clogs, clean and filter. If plants show spotting, check dose and compatibility. If the fogger overheats, stop and check fuel and airflow. Contact the dealer when unsure.
Cleaning and return
Run clean solvent or water through the fogger as directed, wipe and dry. Dispose of residues per label. See returning farm equipment: cleaning and fuel rules.
A sample job
A greenhouse grower rents a ULV fogger to treat whiteflies. The grower measures volume, checks the label, seals the space, fogs at night and waits for re-entry. The fogger is cleaned and returned.
Questions to ask the dealer
- What type and output rate?
- What fuel or power?
- What products was it used with?
- What cleaning is required?
- What damage terms apply?
Keeping records
Record product, dose, volume, date, time, applicator and re-entry. See record keeping for farm equipment rentals.
Timing and environment
Fog when the greenhouse is calm and temperatures are moderate, often in the evening or early morning. Hot, bright conditions raise the risk of leaf burn, and very cool, humid air can leave droplets sitting on foliage, which invites disease. Check the label for temperature limits. Stop fogging if you notice drift through vents, and never fog when wind is pushing air through open sidewalls.
Treating different pests
Whiteflies, thrips, aphids, mites and fungus gnats do not all respond to the same product or timing. Scouting tells you which life stages are present, and the label tells you which stages the product reaches. Many pests need repeat applications spaced by their life cycle. Rotate products with different modes of action to slow resistance, and write the schedule down so you do not repeat the same chemistry back to back.
Adjacent spaces and neighbors
Fog can travel through gaps into attached rooms, offices or neighboring structures. Seal doors, vents and cable gaps, and post notices where people may walk. Tell coworkers and household members when you are fogging. If hired help works nearby, give them the re-entry time in writing.
After the fog settles
Let the greenhouse hold the fog for the label contact time, then ventilate as directed. Test air quality by waiting longer than the minimum if you are unsure. Wash tools and gloves, and launder protective clothing separately from family laundry. Check plants over the next days for injury so you can adjust the dose next time.
Bottom line
Fogging works when the label, math and ventilation are right. Protect people, plants and equipment.
Frequently asked questions
Can I fog any product?
No. Use only labeled products.
How do I calculate dose?
Measure volume and follow the label rate per cubic foot.
Is thermal fogging safe?
It carries fire risk. Keep ignition sources away.
When can I re-enter?
After the label's re-entry interval and ventilation.