Farm Equipment Rentals
Tillage and Soil Preparation Equipment

Moldboard Plow Rentals for Primary Tillage

Rent a moldboard plow for sod, residue burial and seedbed prep: bottoms and sizes, tractor needs, furrow setup, soil moisture, erosion cautions, safety and costs.

6 min read1,240 wordsUpdated November 2026
Moldboard Plow Rentals for Primary Tillage: illustration of a tractor pulling a disc harrow across brown soil

The moldboard plow is the classic tillage tool: a curved steel surface that slices the soil, lifts it and turns it over in a neat furrow. It buries weeds and residue, breaks sod and leaves a rough surface that weathers into a seedbed. Modern farms use it less than they once did, but it is still valuable for renovating pasture, starting gardens and managing certain residue and weed problems. Renting one makes sense when you need only a few acres plowed. This guide explains how it works, what to check and how to run it well.

How a moldboard plow works

Each plow bottom has several parts:

  • Share. The pointed blade that cuts the soil horizontally.
  • Coulter or jointer. A disc or small blade ahead of the bottom that slices the sod and residue.
  • Moldboard. The curved surface that lifts and turns the slice.
  • Landside. A flat plate that presses against the furrow wall and keeps the plow steady.
  • Frog and beam. Structural parts that hold the bottom and connect to the frame.

As the tractor moves forward, the share cuts the slice, the moldboard lifts and rolls it and the slice lands in the previous furrow. Plows come with one to many bottoms. A mounted plow attaches to the three-point hitch, while a pull-type plow attaches to the drawbar and uses wheels for depth control. Reversible plows turn the soil in the same direction on every pass, which avoids dead furrows and back furrows.

When it makes sense

Typical uses include:

  • Breaking old sod or hayfield.
  • Burying heavy residue or manure.
  • Managing perennial weeds or certain diseases and pests.
  • Preparing gardens and small fields.
  • Loosening heavy clay soils in fall for weathering.
  • Renovating pasture. See pasture renovation equipment rentals.

It is less suitable for steep slopes, highly erodible land and systems built around residue cover. Check conservation requirements with your local Farm Service Agency or NRCS office; see the Farmers.gov service center locator. For broader context see renting a plow: types and applications.

Moldboard Plow Rentals for Primary Tillage: illustration of a tractor pulling a disc harrow across brown soil
Illustration: a tractor pulling a disc harrow across brown soil. Original artwork for Farm Equipment Rentals.

Choosing size and tractor

Plow size is expressed by the number of bottoms and the width of each cut, often 12 to 18 inches. A rough rule is that each bottom needs a certain amount of drawbar horsepower, depending on soil and depth. Heavy clay and deep plowing need more. Ask the dealer for the manufacturer's recommendation, and consider:

  1. Horsepower and weight. The tractor needs adequate power and weight to maintain traction.
  2. Four-wheel drive. Helps in wet or heavy soils.
  3. Hitch category. Match the plow's mounting.
  4. Hydraulics. Reversible and hydraulic-adjust plows need remotes.
  5. Tire width. The tractor's right wheels run in the furrow, so tire width must fit.
  6. Transport width and weight. For gates and roads.

See utility tractor rentals and tractor ballast weighting guide.

Soil moisture and timing

Plow when the soil is in the right condition.

  • Too wet. Soil smears, compacts and forms slick clods that dry into hard lumps.
  • Too dry. The plow resists, wears quickly and breaks soil into hard chunks.
  • Just right. Soil crumbles when squeezed and falls apart as it turns.

Fall plowing leaves rough ground exposed to winter freeze and thaw, which helps break clods in heavy soils but increases erosion risk. Spring plowing needs timely follow-up to prepare the seedbed. Match timing to your crop plan. See seasonal rental planning.

Setting up the plow

Correct setup affects everything.

  1. Level side to side and front to back. Use the leveling crank, lift links and top link as in the manual.
  2. Set the width of the first furrow. For a mounted plow, adjust the hitch offset or the landside so the front bottom cuts the right width.
  3. Set depth. Use the hitch, depth wheel or hydraulic control to set a consistent depth.
  4. Adjust the coulters. They should cut just ahead of the bottoms and not too deep.
  5. Check the furrow wheel or tractor tire position. The tractor should run level, not tilted.
  6. Make a test pass, then check the furrow width, depth and soil turning.
  7. Fine-tune. Adjust until the plow runs straight without pulling to the side.

Ask the dealer to show you adjustments, or take notes from the manual. A few minutes at the start saves hours of poor plowing.

Plowing patterns

Common patterns:

  • Lands. Plow in sections, starting at the center and moving outward, leaving a ridge (back furrow) in the middle and a dead furrow at the edges.
  • Back and forth with a reversible plow. No ridge or dead furrow, so fields stay level.
  • Contour plowing. Plow across slopes, along contour lines, to reduce erosion.

Mark the first furrow with a stake or line, and keep your eyes on a point ahead, not the plow.

Erosion and conservation

Plowing leaves bare soil, vulnerable to water and wind. Reduce risk by:

The USDA NRCS and your local conservation district can advise. See your state page.

Safety

  • Wear the seatbelt, and use rollover protection.
  • Never reach under a raised plow. Lower it or use a support.
  • Keep bystanders away.
  • Watch for rocks and roots, which can stop the plow suddenly and shock the tractor. Use plows with breakaway or trip mechanisms where appropriate.
  • Be cautious on slopes and wet ground.
  • Shut off the tractor before working on the plow. See the farm machinery lockout-tagout procedure template.
  • Use transport locks when moving on roads.

See the tractor rollover prevention checklist and the OSHA agricultural operations page.

Costs and terms

Ask about:

  • Daily, weekly and monthly rates.
  • Wear parts, such as shares and points, and who pays for replacement.
  • Shear bolts and spare parts.
  • Delivery and pickup.
  • Damage waiver and exclusions for rock damage.
  • Deposit.

Walk the field and remove rocks, wire and debris before plowing. See renting a rock picker for field clearing and understanding rental agreements.

Inspect before you accept

Check shares, landsides, moldboards, coulters, beams, frogs, hitch pins, wheels, hydraulic hoses and shear bolts. Look for cracks and bent parts. Record condition and photograph existing damage. See understanding rental equipment condition reports.

Follow-up tillage

After plowing, the field is usually rough. Secondary tillage, such as a disk, field cultivator or harrow, breaks clods, levels the surface and creates a seedbed. Plan these passes and rent the equipment together if possible. See disk harrow rentals and field cultivator rentals.

Bottom line

A moldboard plow is a strong tool for sod, residue and heavy soil work. Choose the right size, set it up carefully, plow at the right moisture and protect the land from erosion. Plan follow-up tillage and consider alternatives if your fields are sloped or sensitive.

Frequently asked questions

How many plow bottoms can my tractor pull?

It depends on horsepower, weight, soil and depth. Ask the dealer for the manufacturer's guidance for your tractor and conditions.

What is a reversible plow?

A plow with two sets of bottoms that flip, so soil is always turned in the same direction. It leaves no ridge or dead furrow.

Is plowing bad for the soil?

It can increase erosion and organic matter loss, especially on slopes. Use conservation practices and consider alternatives.

When is soil ready to plow?

When a squeezed handful crumbles rather than forming a sticky ball or hard lump.

Keep reading

Tillage and Soil Preparation Equipment

Renting a Plow: Types and Applications

Understand plow types for rental: moldboard, chisel, disc and subsoil plows, their uses, tractor needs, soil conditions, erosion concerns and when no-till is better.

Tillage and Soil Preparation Equipment

Offset Disk Rentals for Heavy Residue

Rent an offset disk to handle heavy residue, sod and brush: how it works, sizes and blade types, tractor requirements, transport, settings, safety and cost planning.

Tillage and Soil Preparation Equipment

Soybean Planter Rentals: Narrow vs Wide Rows

Renting a soybean planter or drill: narrow versus wide rows, seeding rates, depth, meters, drills versus planters, residue, tractor needs, timing and what to check at pickup.

Tillage and Soil Preparation Equipment

Laser Leveling Rentals for Irrigation Prep

Rent laser or GPS leveling gear for irrigated fields: survey, target grade, scraper setup, soil handling, tolerance, water savings, costs and when to hire an experienced crew.