A fence is only as good as its posts, and the posts are only as good as the holes. Digging by hand is slow and punishing, while a rented auger can bore dozens of holes in an afternoon. Augers attach to tractors, skid steers and mini excavators, and handheld models exist for small jobs. This guide explains the types, how to choose, how to avoid trouble and how to keep fingers and legs intact.
Types of augers and diggers
- Handheld one-person or two-person gas augers. Portable, good for a few holes and tight spaces, but physically demanding and prone to kickback in tough soil.
- Tractor PTO augers. Mount on the three-point hitch and use the PTO. Common on farms for fence lines and orchards.
- Skid-steer augers. Hydraulic drives that attach to the quick-attach plate. See renting a skid steer.
- Mini excavator augers. Provide positioning and power in rough sites. See mini excavator rentals.
- Manual post-hole diggers. Clamshell tools for small jobs and fine adjustments.
- Post drivers. Not augers, but an alternative that drives posts without digging.
Choosing the right bit
Bit size and length matter:
- Diameter. Should be a few inches larger than the post, and larger for gate posts and braces. Common sizes range from about 6 to 24 inches.
- Length. Must exceed the hole depth. Extensions may be available.
- Flight design. Different styles handle clay, sand or rocky soil.
- Teeth and tips. Rock teeth cut harder soils, while standard points work in softer ground.
- Auger drive rating. Must match the machine's torque and hydraulic flow.
Ask the dealer what bits are included and what extras cost. Having multiple sizes can save time.
Planning the fence line
- Measure and mark. Stake the line and corners, and mark each post location.
- Decide on depth and spacing. Frost depth, soil and fence type influence depth.
- Check for utilities. Call 811, and locate buried lines, tile and septic systems.
- Plan corners and gates. These need bigger holes and deeper posts.
- Schedule concrete or backfill. Decide whether to set posts in concrete or tamped soil.
- Order materials. Posts, braces, wire, gates and hardware.
For long fence lines consider hiring a fence contractor or renting a post driver. See renting equipment for a one-time farm project and renting a trencher for irrigation and fencing.
Soil and ground conditions
| Condition | Challenge | Tip |
|---|---|---|
| Rocky | Auger bounces, may stall | Use rock teeth or an excavator |
| Roots | Auger wraps and stops | Cut roots first |
| Wet clay | Sticks to the flights | Clean often, work slowly |
| Dry hard clay | Slow progress | Wet the spot or use a stronger machine |
| Sand | Walls cave | Use a sleeve or move quickly to set posts |
| Frozen ground | Hard to bore | Wait or use specialized equipment |
Probe test holes first. If an auger hits a large rock, stop and reposition rather than forcing it.
Using the auger safely
Augers are dangerous. They grab clothing, hands and feet, and they can kick back and strike the operator.
- Read the manual and get a demonstration.
- Wear boots, gloves, eye protection and hearing protection. Avoid loose clothing, jewelry and long hair.
- Keep hands and feet clear of the auger.
- Never hold the auger by hand to guide it.
- Brace handheld augers properly, and be ready for kickback. Two-person models need good communication.
- Keep bystanders and animals away.
- Do not lift the auger while it is spinning.
- Stop the auger before clearing soil.
- Cover or mark open holes so people and livestock do not fall in.
- Shut off the tractor and remove the key before leaving the seat.
See the PTO safety shield inspection form, the farm machinery lockout-tagout procedure template and the OSHA agricultural operations page.
Tractor and skid-steer compatibility
Check the following:
- Horsepower. The auger must not exceed the tractor's PTO capacity.
- Hitch category. Match the three-point hitch.
- PTO speed. 540 RPM is typical.
- Hydraulic flow. For skid steers and excavators.
- Auger weight and stability. Large augers can tip small tractors. Add front weight if needed.
- Shield and driveline condition.
See renting a tractor: what to know before you book and tractor rental attachments.
Costs and terms
Auger rentals are usually daily or half-day for handheld models, with different rates for tractor or skid-steer attachments. Ask about bit rentals, deposits, damage waivers and cleaning. Bits are sharp and can be damaged by rocks, so ask about wear policies. See understanding rental agreements and how to budget for farm equipment rentals.
Finishing the posts
After digging, set posts quickly before holes cave in. Plumb and brace posts, backfill in layers, tamp firmly and allow concrete to cure if used. Check line and height. For wire fences, tension only after corner and brace posts are set and secure. See pasture renovation equipment rentals for related pasture work.
Inspect before you leave
Check the auger flights, teeth, shaft, gearbox oil, hoses, shields and mounting pins. Test it before you leave if possible. Record existing damage. See understanding rental equipment condition reports.
A sample fence day
A crew of two can set a few dozen posts in a day with a tractor auger when the soil cooperates. Start at a corner, drill the brace and corner holes first with the larger bit and set those posts before moving on. Then run string between the corners and drill line-post holes at the spacing in your plan, stopping to clear soil from the flights whenever it packs. Keep a probe bar handy for hidden rocks, and carry a hand digger for the last few inches in tight spots. If rain threatens, cover open holes so they do not fill with water and slump. Plan to set posts the same day you drill, since holes left overnight can collapse or become a hazard for livestock.
Mistakes to avoid
- Choosing a bit that is too narrow for a good backfill collar.
- Drilling every hole before setting any post.
- Forcing a stalled auger instead of stopping and clearing it.
- Standing with legs near the spinning flights.
Bottom line
An auger can turn days of digging into hours. Choose the right type and bit, know your soil, plan the fence layout and use the machine safely. For rocky ground or very long lines, consider an excavator, post driver or contractor.
Frequently asked questions
What auger size do I need for fence posts?
Generally a few inches larger than the post diameter, with larger holes for corners and gates. Confirm with your fence plan.
Can a handheld auger dig in rocky soil?
It struggles and can kick back. Use a tractor or excavator auger with rock teeth, or choose another method.
Do I need to call 811 before auguring?
Yes. Buried utilities can be hit by auger holes.
Should I use concrete for fence posts?
It depends on the fence type and soil. Corner and gate posts often benefit from concrete, while line posts may be tamped.